en:projects:4e4th:start
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
en:projects:4e4th:start [2018-05-12 12:03] – [Glossary] mka | en:projects:4e4th:start [2018-05-12 12:17] – [Acknowledgements] mka | ||
---|---|---|---|
Line 237: | Line 237: | ||
DECIMAL | DECIMAL | ||
: blink BEGIN | : blink BEGIN | ||
- | red cset green cclrb 100 MS | + | red csetb green cclrb 100 MS |
- | red cclr green csetb 100 MS | + | red cclrb green csetb 100 MS |
KEY? UNTIL ; | KEY? UNTIL ; | ||
Line 258: | Line 258: | ||
Ti's engineers assume that you program your LaunchPad using C or Assembler. Therefore TI offers so called Integrated Development Environment (IDE) software - the IAR " | Ti's engineers assume that you program your LaunchPad using C or Assembler. Therefore TI offers so called Integrated Development Environment (IDE) software - the IAR " | ||
- | But there is an odd loophole: complete projects may be developed with Kickstart, and programmed with another program. | + | We used Naken Assembler instead. https:// |
Line 319: | Line 319: | ||
===== Programmer ===== | ===== Programmer ===== | ||
- | You find the 4E4th binary image at the Forth-Gesellschaft Repository: http:// | + | You find the 4E4th binary image at GitHub, see section Bootstrap Loading for a link. It has to be loaded into the MCU using a suitable programmer. |
== Windows XP and Windows 7 == | == Windows XP and Windows 7 == | ||
Line 465: | Line 465: | ||
If I remove the LaunchPad from the USB while TeraTerm still is running, the connection of the two remains disturbed. Thus Hotplug does not go. So far it only helps to close TeraTerm. Afterwards (!) disconnect LaunchPad from USB, wait for the sound sequence, connect again, and wait for the sound sequence again, then open the terminal.
When using the FET-Pro430 Programmer, follow those instructions, |
If I remove the LaunchPad from the USB while TeraTerm still is running, the connection of the two remains disturbed. Thus Hotplug does not go. So far it only helps to close TeraTerm. Afterwards (!) disconnect LaunchPad from USB, wait for the sound sequence, connect again, and wait for the sound sequence again, then open the terminal.
When using the FET-Pro430 Programmer, follow those instructions, | ||
+ | |||
+ | Looks like the newest TeraTerm can hot plug the Launchpad. mk 20180510 | ||
====== Acknowledgements ====== | ====== Acknowledgements ====== | ||
Line 471: | Line 473: | ||
Thanks to Dirk Bruehl for his untiring and altruistic support of the 4E4th Project, by ordering the appropriate hardware and encouraging with many hints and ideas to go on until CamelForth was running on the LaunchPad. | Thanks to Dirk Bruehl for his untiring and altruistic support of the 4E4th Project, by ordering the appropriate hardware and encouraging with many hints and ideas to go on until CamelForth was running on the LaunchPad. | ||
mk 03-14-2012 | mk 03-14-2012 | ||
+ | |||
+ | Many, many thanks to Brad Rodriguez again for porting CamelForth to Naken Assembler! And to Juergen Pintaske for talking me in porting 4e4th to Naken Assembler as well. | ||
====== Links ====== | ====== Links ====== |
en/projects/4e4th/start.txt · Last modified: 2018-05-13 00:17 by mka