Forth-eV Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== TASTO? ======

A key (Italian tasto, Latin clavis) or a button is a control element that is operated by pressing and automatically returns to its original position when released.

Forth has ''KEY?'' and ''KEY'' to query the computer's keyboard. I therefore call the query of a different individual key something else. Figure below shows such a key.

{{:pfw:weissertaster.png?100|The small white button is on the breadboard at the bottom right of the picture.}}

At [[en:pfw:clavis|CLAVIS?]] you can find out more about it.


===== Implementation for MSP430G2553 =====

Here, the button is connected to pin 7 of port 1 of the MSP430G2553 microprocessor MCU. See circuit diagram in code.


==== I/O ====

This circuit provides a digital input, with the pin itself being the voltage source.


==== Pseudo code ====

<code>
Function:  PININ ( mask -- ) 
           configure pin as input
Function:  TASTO? ( mask -- f )  \ flag is true if the key is not pressed (high level at pin)
           check digital voltage level 
</code>


==== Forth implementation (noForth) ====

The port pins are configured using registers.
The configuration register table is specified in the code.
The interrupt register indicates whether a falling edge was present.

In the direction register, P1.7 is set to digital IN.
The integrated **pull-up resistor is activated** to support the high level.
No interrupt should occur, so it is disabled. 
The pin is used in the I/O function.

Try more or fewer than five queries to eliminate the bouncing. (More on the [[pfw:topicofbouncing|topic of bouncing]].)

<code>
\ test button
\ TI MSP430G2553 Launchpad with noForth mv 2553 240101 

(* 
History
20250609 P1.7 digital input

addr acronym registername
020  P1IN    Input
021  P1OUT   Output 
022  P1DIR   Direction
023  P1IFG   Interupt Flag
024  P1IES   Interrupt Edge Select
025  P1IE    Interrupt Enable
026  P1SEL   Port Select
041  P1SEL2  Port Select2
027  P1REN   Resistor Enable 

     Pin1.7--<---R---Button---GND
	 R=47K
*)

hex

80 constant pin7 \ mask for pin7 of port
		   
: PININ ( mask -- ) \  make pin to input 
  ( 020 )    \ P1IN    Input, read only
dup 021 *bis \ P1OUT   Output, pullup resistor set
dup 022 *bic \ P1DIR   Direction to IN
dup 023 *bic \ P1IFG   Interupt Flag, cleared
dup 024 *bic \ P1IES   Interrupt Edge Select, is irrelevant here.
dup 025 *bic \ P1IE    Interrupt Enable, off
dup 026 *bic \ P1SEL   Port Select,  I/O
dup 041 *bic \ P1SEL2  Port Select2, I/O
    027 *bis \ P1REN   Resistor Enable, set
  ;
  

: TASTO? ( mask -- f )  \ Query button. debounced
  >r
  r@ 020 bit* 3 ms 
  r@ 020 bit* 3 ms
  and
  r@ 020 bit* 3 ms
  and  
  r@ 020 bit* 3 ms
  and
  r@ 020 bit* 3 ms
  and  
  r> =
  ;

\ test  mk
: tt ( -- )
  pin7 pinin 
  begin  ( 100 ms )  \ add more ms if you like
  pin7 tasto? .
  key? until 
  ;

shield nn\
freeze
( finis)
</code>

==== Background information ====

You can find them there: [[en:pfw:clavis|CLAVIS?]]


===== Contributions =====


===== Alternative Implementations =====

You have another approach?

Please add it at the end of this document.

Sign in to post a comment.